Rotor-EZ for Hy-Gain Controllers by Ham Supply/Idiom Press – Invented, Patented and Manufactured in the USA “Point and Shoot” Rotor-EZ (with or without computer control RS-232) and Rotor-EZ Serial Upgrade Kit (for existing non RS-232 Rotor-EZ to RS-232) for Hy-Gain Controllers by Ham Supply/Idiom Press are now IN STOCK and ready to ship. Our Hands-Free Rotor-EZ controller installs in any CDE, Ham-M, Ham-II, Ham III, Ham IV or TailTwister rotator control box with three paddles on the rotator control box.

You have 3 paddles on your Hy-Gain rotor control box? Our Rotor-EZ will work for you! Do you own one or more of these fine rotators? If you do, you know that for all their faults they are still some of the best rotators available. Now, by adding Rotor-EZ to your rotator control, you can bring these units up to date with all the features of rotators or rotator controls costing hundreds of dollars more, all while eliminating the faults! Rotor-EZ starts by adding a really neat and unique auto-point feature, which is easier to use and more accurate than the “preset” capability offered by any competitive rotator or rotator control.

This allows you to quickly, simply and accurately point the antenna, then press the brake paddle momentarily and let go, freeing your hands for other things, perhaps such as panic band change thanks to a packet spot called in for a needed station. Rotor-EZ protects your rotator, with electronic end stops, provision for coasting, and start-up jam prevention, especially useful for TailTwisters. You lose no utility with these features, but add significant protection for your rotator, antenna and tower. These features can be bypassed if desired. Rotor-EZ offers full support for antennas set at 90° to the main antenna. Ground a circuit lead and the meter needle moves 90 degrees to show the bearing for the offset antenna. And, an LED lamp pulses to remind you that you are in the offset mode.

Rotor Ham IV. Uploaded by javier. INSTRUCTION MANUAL GENERAL DESCRIPTION The HAM IV rotator consists of a bell type rotator. HAM IV Rotator Replacement Parts. HY-GAIN HAM-IV Medium - Duty Rotator with Controller - Up to 15 Square Feet Wind Area - 110 Volts.

Perfect for the forty meter “shorty-forty” or the WARC band offset antenna sharing the mast with your tri-bander! Full RS232 control is now an affordable option for older Rotor-EZ installations with the Rotor-EZ Serial Upgrade Kit (non RS-232 to RS-232), offering full compatibility with all the popular logging and contesting programs. Osnove Knjigovodstva Pdf here. Rotor-EZ is offered as circuit board kit or prewired and tested board that you add to your rotator control unit.

Everything needed except solder and tools is included. Featuring sophisticated microcircuitry and firmware, the board can be assembled and installed in a few hours. All functions are accomplished in the control unit, and no tower climbing is required to fully implement Rotor-EZ. The board fits in and works with all CDE, Ham-M, Ham-II, Ham III, Ham IV or TailTwister rotator control units that have three control paddles on the front.

Crack Do Deluxe Ski Jumping 4. If you do not have the time to add Rotor-EZ to your rotator, contract assembly and installation are available. For further details. Operating Modes Manual Mode: The rotator control works as before; pressing the brake and a paddle turns the antenna. Fifa 14 Latest Fix Crack V5. However, Rotor-EZ provides an automatic 5 second time delay before the brake resets after paddle release, allowing the antenna to stabilize before the brake locks (note that after Rotor-EZ is installed, the LED’s – if supplied in the original configuration of the box – do not light when the unit is manually controlled, although the meter functions as before.

However, normal operation using Rotor-EZ will rarely require manual operation, and when using the Rotor-EZ features, the LED’s do illuminate as appropriate). Auto-Point Mode: What was the calibration knob becomes your pointing control (the calibration function is now an internal one). When you turn the knob, the meter function automatically switches from reading the existing antenna bearing and instead becomes the aiming pointer, captured by the aiming logic of the circuit. Rotate the knob, moving the needle easily, precisely and accurately to your desired bearing. Then, a brief press of the brake paddle begins rotation, and your hands are free! The meter needle returns to its normal function, tracking the antenna as it moves.

When the antenna reaches the new bearing, rotation stops, and after a 5 second delay the brake sets. LED’s signal the motion, and how near the antenna is to the new bearing. If the TailTwister program option is selected (all program options are selected by PC board jumpers), when command execution begins the rotator first pulses in the opposite direction for 1 second in case the brake is stuck, pauses 1 second, then turns in the proper direction.